TAILIEUCHUNG - Analog and InterfaceAnalog and Interface Guide – Volume 1 phần 2

Chế độ đầu tiên sẽ được nếu bạn muốn tham khảo một lập trình, điều chỉnh, DC. Trong chế độ này, phần kỹ thuật số của mạch điện chỉ được sử dụng thường xuyên và chắc chắn không phải trong quá trình hoạt động bình thường. Chế độ thứ hai sẽ được nếu bạn sử dụng mạch như một máy phát sóng tùy ý. | Analog and Interface Guide - Volume 1 An Intuitive Approach to Mixed Signal Layout - Part 3 Figure 2 A 16-bit DAC can be built using three 8-bit digital potentiometers and three amplifiers to provide 65 536 different output voltages. If Vdd is 5V in this system the resolution or LSB size of this DAC is mV. This circuit can be used in two basic modes of operation. The first mode would be if you wanted a programmable adjustable DC reference. In this mode the digital portion of the circuit is only used occasionally and certainly not during normal operation. The second mode would be if you used the circuit as an arbitrary wave generator. In this mode the digital portion of the circuit is an intimate part of the circuit operation. In this mode the risk of capacitive coupling may occur. The first pass layout of the circuit in Figure 2 is shown in Figure 3. This circuit was quickly designed in our lab without attention to detail. The consequences of placing digital traces next to high impedance analog lines were overlooked in the layout review. This speaks strongly to doing it right the first time but to our benefit this article will illustrate how to identify the problem and make significant improvements. Device Specification Purpose Digital Potentiometers MCP42010 Number of bits 8-bits Determines the overall LSB size and resolution of the circuit. Nominal resistance resistive element 10 kQ typ The lower this resistance is the lower the noise contribution will be to the overall circuit. The trade off is that the current consumption of the circuit is high with these lower resistances. DNL 1 LSB max Good Differential Non-Linearity is needed to insure no missing codes occur in this circuit which allows for a possible 16-bit operation. Voltage Noise Density for half of the resistive element 9 nV .Hz @ 1 kHz typ If the noise contribution of these devices is too high it will take away from the ability to get 16-bit noise free performance. Selecting lower resistive .

TỪ KHÓA LIÊN QUAN
TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.