TAILIEUCHUNG - Migrating from RIP to EIGRP Host B 192.168.3.2 /24 Fa0/0 192.168.3.1 /24 S0/0 192.168.1.1 /24 S0/1 192.168.2.1 /24 S0/0 192.168.1.2 /24 Fa0/0 10.0.0.1 /8 S0/0 192.168.2.2 /24 Fa0/0 10.0.0.2 /8 Host A 10.0.0.11 /8 Vista SanJose1 SanJose2 Objective In this lab, you configure RIPv2 and then EIGRP so that you can compare their metric calculations. Scenario International Travel Agency (ITA) currently uses RIPv2 as its interior gateway protocol. You have been asked to migrate its network to EIGRP. Ste

Build and configure the network according to the diagram. Note: Host A and Host B are not required to complete this lab, but they might be used in testing or as Telnet clients. If used, Host A's gateway may be either SanJose1 router or the SanJose2 router. | Migrating from RIP to EIGRP Host B 24 Fa0 0 24 S0 0 24 Vista S0 0 24 Fa0 0 8 S0 1 24 S0 0 24 SanJosel SanJose2 Fa0 0 8 Host A 8 Objective In this lab you configure RIPv2 and then EIGRP so that you can compare their metric calculations. Scenario International Travel Agency ITA currently uses RIPv2 as its interior gateway protocol. You have been asked to migrate its network to EIGRP. Step 1 Build and configure the network according to the diagram. Note Host A and Host B are not required to complete this lab but they might be used in testing or as Telnet clients. If used Host A s gateway may be either SanJosel router or the SanJose2 router. On all three routers configure RIPv2 and enable updates on all active interfaces with the network command. Here are some sample commands for SanJosel SanJose1 config router rip SanJose1 config-router version 2 SanJose1 config-router network SanJose1 config-router network Use ping and show ip route to verify full connectivity within the network. 1 - 3 Semester 5 Advanced Routing - Lab Copyright 2001 Cisco Systems Inc. Step 2 As you migrate to EIGRP you decide to leave RIP running on all the routers to avoid a loss of connectivity. On SanJosel and SanJose2 configure EIGRP for Autonomous System 24 as shown below. Do not configure Vista for EIGRP yet. SanJose1 config router eigrp 24 SanJose1 config-router network SanJose1 config-router network and SanJose2 config router eigrp 24 SanJose2 config-router network SanJose2 config-router network Step 3 From Vista s console issue the show ip route command. Because you have not yet configured EIGRP on this router you should have a route to the 8 network via RIP. 1. What is the administrative distance of this route 2. What is the metric of this route Enable debug so that changes to the routing table will be .

TỪ KHÓA LIÊN QUAN
TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.