TAILIEUCHUNG - cisco 640 802 ccna portable command guide 2008 phần 8

Thay đổi bộ đếm thời gian hello-trì hoãn đến 4 giây trên VLAN 5 Thay đổi bộ đếm thời gian chuyển tiếp, chậm trễ đến 20 giây trên VLAN 5 Thay đổi bộ đếm thời gian tối đa lão hóa đến 25 giây trên VLAN 5Chú ý: Đối với các lệnh thời gian hello-, phạm vi từ 1 đến 10 giây. | Spanning Tree Protocol 143 Configuring STP Timers Switch config spanning-tree vlan 5 hello-time 4 Changes the hello-delay timer to 4 seconds on VLAN 5 Switch config spanning-tree vlan 5 forward-time 20 Changes the forward-delay timer to 20 seconds on VLAN 5 Switch config spanning-tree vlan 5 max-age 25 Changes the maximum-aging timer to 25 seconds on VLAN 5 NOTE For the hello-time command the range is 1 to 10 seconds. The default is 2 seconds. For the forward-time command the range is 4 to 30 seconds. The default is 15 seconds. For the max-age command the range is 6 to 40 seconds. The default is 20 seconds. CAUTION Cisco recommends caution when using this command. Cisco further recommends that the spanning-tree vlan x root primary or the spanning-tree vlan xroot secondary command be used instead to modify the switch timers. Verifying STP Switch show spanning-tree Displays STP information Switch show spanning-tree active Displays STP information on active interfaces only Switch show spanning-tree brief Displays a brief status of the STP Switch show spanning-tree detail Displays a detailed summary of interface information Switch show spanning-tree interface gigabitethernet 0 1 Displays STP information for interface gigabitethernet 0 1 Switch show spanning-tree summary Displays a summary of port states Switch show spanning-tree summary totals Displays the total lines of the STP section Switch show spanning-tree vlan 5 Displays STP information for VLAN 5 144 Spann ing Tree Protocol Optional STP Configurations Although the following commands are not mandatory for STP to work you might find these helpful to fine-tune your network. PortFast Switch config interface fastethernet 0 10 Moves to interface configuration mode. Switch config-if spanning-tree portfast Enables PortFast on an access port. Switch config-if spanning- tree portfast trunk Enables PortFast on a trunk port. WARNING Use the portfast command only when connecting a single end station to an access or trunk .

TỪ KHÓA LIÊN QUAN
TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.