TAILIEUCHUNG - PSIM User Manual phần 6

Này cung cấp một xung TTL tương thích với các cạnh sắc nét và khả năng miễn dịch tiếng ồn cao để kết nối với bộ điều khiển thông qua một dây cáp chiếu. Đối với một động cơ ba pha không chổi than dc, ba công tắc phòng được đặt cách nhau 120 ° điện. ra và được gắn trên khung stator. Các thiết lập của nam châm gây ra có thể là một bộ riêng biệt của nam châm, hoặc nó có thể sử dụng. | Chapter 3 Control Circuit Components Example The following circuit performs the function of selecting the maximum value out of two inputs. When Va is greater than Vb the comparator output will be 1 and Vo Va. Otherwise Vo Vb. THD Block For an ac waveform that contains both the fundamental and harmonic components the total harmonic distortion of the waveform is defined as THD V -- V1 Jv - V rms 1 --------- V1 where V1 is the fundamental component rms Vh is the harmonic rms value and Vrms is the overall rms value of the waveform. The THD block is modelled as shown below. A second-order band-pass filter is used to extract the fundamental component. The center frequency and the passing band of the band-pass filter need to be specified. 3-18 PSIM User Manual Logic Components Attributes Parameters Description Fundamental Frequency Passing Band Fundamental frequency of the input in Hz Passing band of the band-pass filter in Hz Example In the single-phase thyristor circuit below a THD block is used to measure the THD of the input current. The delay angle of the thyristor bridge is chosen as 30o. For the THD block the fundamental frequency is set at 60 Hz and the passing band of the filter is set at 20 Hz. The simulation results are shown on the right. One of the THD block output is the input current fundamental component is1. By comparing the phase difference between the input voltage vs and the current is 1 one can calculate the input displacement power factor. This together with the THD value can be used to calculate the input power factor. Logic Components Logic Gates Basic logic gates are AND OR XORGATE exclusive-OR NOT NAND and NOR gates. Images PSIM User Manual 3-19 Chapter 3 Control Circuit Components Set-Reset Flip-Flop There are two types of set-reset flip-flops. One is edge-triggered and the other is level-triggered. Attributes Parameters Description Trigger Flag Trigger flag 0 edge-triggered 1 level-triggered The edge-triggered flip-flop .

TỪ KHÓA LIÊN QUAN
TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.