TAILIEUCHUNG - Cable a network similar to the one in the diagram. The configuration output used in this lab is produced from a 2950 series switch. Any other switch used may produce different output. The following steps are to be executed on each switch unless specifically instructed otherwise. Start a HyperTerminal session. Note: Go to the erase and reload instructions at the end of this lab. Perform those steps on all switches in this lab assignment before continuing.

Tham khảo tài liệu 'cable a network similar to the one in the diagram. the configuration output used in this lab is produced from a 2950 series switch. any other switch used may produce different output. the following steps are to be executed on each switch unless specifically instructed otherwise. start a hyperterminal session. note: go to the erase and reload instructions at the end of this lab. perform those steps on all switches in this lab assignment before continuing.', công nghệ thông tin | Cisco SrsTEMS Lab Managing Switch Startup Configuration Files FA0 1 Switch Designation Switch Name Enable Secret Password Enable VTY and Console Passwords VLAN 1 IP Address Default Gateway IP Address Subnet Mask ị Switch 1 I AL Switch class cisco Straight-through cable --------------------- Serial cable S__ Console Rollover . Crossover cable Objective Create and verify a basic switch configuration. Backup the switch startup configuration file to a TFTP server and then restore it. Background Preparation Cable a network similar to the one in the diagram. The configuration output used in this lab is produced from a 2950 series switch. Any other switch used may produce different output. The following steps are to be executed on each switch unless specifically instructed otherwise. Instructions are also provided for the 1900 Series switch which initially displays a User Interface Menu. Select the Command Line option from the menu to perform the steps for this lab. Start a HyperTerminal session. Note Go to the erase and reload instructions at the end of this lab. Perform those steps on all switches in this lab assignment before continuing. Step 1 Configure the switch Configure the hostname access and command mode passwords as well as the management LAN settings. These values are shown in the chart. If problems occur while performing this configuration refer to the Basic Switch Configuration lab. Step 2 Configure the host attached to the switch Configure the host to use the same subnet for the address mask and default gateway as on the switch. This host will act as the TFTP server in this lab. Be sure to take note of the IP address assigned. 1 - 6 CCNA 3 Switching Basics and Intermediate Routing v - Lab Copyright 2003 Cisco Systems Inc. Step 3 Verify connectivity a. To verify that the host and switch are correctly configured ping the switch IP address from the host. b. Was the ping successful .

TỪ KHÓA LIÊN QUAN
TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.