TAILIEUCHUNG - Componentwise thermodynamic analysis of thermal power plant by designed software

Thermodynamic/exergy analysis is performed at different inlet pressure conditions of steam and identified conditions at which the performance of the plant is best. This software also helps to develop correction factor curves for power and heat rate at different inlet pressure conditions. | Journal of Automation and Control Engineering Vol. 4, No. 4, August 2016 Componentwise Thermodynamic Analysis of Thermal Power Plant by Designed Software Ankur Geete Mechanical Engineering Department, S. D. Bansal College of Technology, Indore, Madhya Pradesh, India Email: ankur_geete@ Abstract—This research work is based on 120MW thermal power plant which has five major components. The components are–steam turbine, condenser, feed water heaters and boiler. Each component is having its own importance and it effects the performance of power plant. In this research work component wise thermodynamic/exergy analysis is done. For analysis, more general software is designed. By this software, thermodynamic/exergy analysis is performed at different inlet pressure conditions of steam and identified conditions at which the performance of the plant is best. This software also helps to develop correction factor curves for power and heat rate at different inlet pressure conditions. that, steam is reheated and then enters into IP turbine. In IP turbine, steam is expanded and some amount of steam is extracted from two extraction points for feed water heater number 5 and deaerator respectively. After expansion in IP turbine, steam is again extracted for feed water heater 3. Then finally steam enters into LP turbine where it is expanded and steam is again extracted from two extraction points for feed water heater number 2 and feed water heater number 1 respectively. Then wet steam is condensed and converted into water in condenser. After heating in different feed water heaters, water enters again into the boiler with the help of feed water pump [1]. Some important terms which are used during analysis of power plant–(1) Correction factor–it is the ratio of designed output to actual output. Example–correction factor for power is the ratio of designed power to actual power output (net power) [1]. (2) Flow function-it shows the relation between mass flow rate, specific .

• Cơ khí - Chế tạo máy
• Journal of Automation and Control Engineering
• Componentwise thermodynamic analysis
• Thermal power plant by designed software
• Thermal power plant
• Heat rate and Inlet pressure
• Increasing the productivity of automation tool by developing socket
• Automation tool by developing socket
• Auto report generated
• The automation tool
• Abnormality management in industrial automation systems
• Industrial automation systems
• Future industrial automation systems
• Abnormality management approach
• Sliding mode based relative pose synchronous control
• Space autonomous rendezvous
• Relative pose synchronous control
• The control system design
• The sliding mode control law
• Application of pressure control type quasiservo valve
• Force control system
• The quasi servo valve
• The pneumatic cylinder
• Robust vehicle suspension system
• Converting active & passive control
• A vehicle to semi active control system analytically
• Semi Active Vehicle System
• Environmental control of a greenhouse system
• NI embedded systems technology
• The soil moisture
• The Engineering School of Bahrain Polytechnic
• Design of control system for 3D printer
• DSP and FPGA
• Control system for 3D printer
• Closed loop control
• Improving performances of a cement rotary kiln
• A model predictive control solution
• Cement rotary kiln
• Advanced process control
• Model predictive control
• Active learning in motor control and matlab simulation
• Active learning in motor control
• Servo motors of the simulation of neural networks
• Motion of a robot arm
• Redundancy and operation of power control system
• A deep space small probe
• Functions of redundancy
• Power Control Unit
• Closed loop speed control of miniature brushless DC motors
• Closed loop speed control
• Miniature brushless DC motors
• Delta Connected BLDC motors
• Adaptive wavelet backstepping control
• Class of mimo underactuated systems
• Multi input multi output
• Proposed control scheme
• Adaptive backstepping controller
• Hybrid position force control for a stewart platform
• Hybrid position force control
• The work surface
• The stewart platform
• Robust control of double inverted pendulum system
• Double inverted pendulum system
• Reference trajectory control
• The dynamic modeling
• Speech recognition in human computer interactive control
• Computer interactive control
• HTK and Sphinx
• Vietnamese speech recognition
• Human computer interaction
• Command shaped robust control of a flexible spacecraft
• Command shaped robust control
• Strong cross couplings
• Loop shaping design
• Optimal control of vehicle active suspension system
• Vehicle active suspension system
• The active suspension system
• LQR control technique
• Mimo fuzzy control for autonomous mobile robot
• Mimo fuzzy control
• Autonomous mobile robot
• Implementation of multi input multi output
• Reach defined target
• Asynthesis method of robust cascade control system
• Robust cascade control system
• Imposes robust conditions
• Soft oscillation index
• Efficient adaptive fuzzy control scheme for industrial manipulators
• Degree of freedom
• Fuzzy control scheme
• IMO nonlinear second order systems
• Multilevel inverter topology and control techniques
• Reduce electromagnetic interference
• Control strategies employed
• Linear quadratic optimal control problem of stochastic switching systems
• Linear quadratic optimal control problem
• Stochastic switching systems
• Non invariant linear systems
• Investigation of hybrid adaptive control schemes
• Needle free jet injection system
• Hybrid adaptive control schemes
• Needle free jet injection
• Modelling and simulations
• Development of a new algorithm
• Control excitation of particular mode of a building
• Particular mode of a building
• Sliding mode control
• Control of electric motor machine tools
• Self organizing fuzzy logic controller
• Modify the control rule
• The self organizing fuzzy logic controller