TAILIEUCHUNG - An investigation on effects of wire-EDM machining parameters on surface roughness of newly developed DC53 die steel

(BQ) This paper investigated the effects of machining parameters on surface roughness of wire EDMed DC53 die steel. The investigated machining parameters were pulse-on time, pulse-off time, pulse-peak current, and wire tension. Analysis of variance (ANOVA) technique was used to find out the parameters affecting the surface roughness. Assumptions of ANOVA were discussed and then examined through residual analysis. Quantitative testing methods on residual analysis were employed in place of the typical qualitative testing techniques. Results from ANOVA show that pulse-on time and pulse-peak current are significant variables to surface roughness of wire-EDMed DC53 die steel. The surface roughness of test specimen increased as these two variables increased. | Journal of Materials Processing Technology 187–188 (2007) 26–29 An investigation on effects of wire-EDM machining parameters on surface roughness of newly developed DC53 die steel K. Kanlayasiri a,∗ , S. Boonmung b a b Department of Industrial Engineering, Faculty of Engineering, King Mongkut’s Institute of Technology Ladkrabang, Bangkok 10520, Thailand Department of Agricultural Engineering, Faculty of Engineering, King Mongkut’s Institute of Technology Ladkrabang, Bangkok 10520, Thailand Abstract DC53 is a newly developed cold die steel from Daido Steel, Japan. It is an improvement over the familiar cold die steel SKD11. Because DC53 is a new die steel, only little information is available in literature for its machining characteristics. This paper investigated the effects of machining parameters on surface roughness of wire EDMed DC53 die steel. The investigated machining parameters were pulse-on time, pulse-off time, pulse-peak current, and wire tension. Analysis of variance (ANOVA) technique was used to find out the parameters affecting the surface roughness. Assumptions of ANOVA were discussed and then examined through residual analysis. Quantitative testing methods on residual analysis were employed in place of the typical qualitative testing techniques. Results from ANOVA show that pulse-on time and pulse-peak current are significant variables to surface roughness of wire-EDMed DC53 die steel. The surface roughness of test specimen increased as these two variables increased. © 2007 Published by Elsevier . Keywords: DC53 die steel; Wire-EDM; Surface roughness; Analysis of variance; Residual analysis 1. Introduction Die-making industry is very important to down-stream industries. Any technological changes in the die-making industry surely affect those down-stream manufacturing. One of those technological developments is novel materials for making various kinds of dies. New die steels have been continuously introduced to the die manufacturers, and affect

• Cơ khí - Chế tạo máy
• DC53 die steel
• Wire EDM
• Surface roughness
• Analysis of variance
• Residual analysis
• Analysis of residuals
• Multiple regression
• Safety analysis of increase in heat removal from reactor coolant system
• Inadvertent operation of passive residual heat removal
• Passive residual heat removal
• The reactor coolant system
• Nuclear engineering and technology
• On the fly estimation strategy
• Uncertainty propagation in two step monte carlo calculation
• Residual radiation analysis
• Accurate two step MC calculations
• BMC Musculoskeletal Disorders
• Lumbar disc herniation
• Residual low back pain
• Visual analog scale
• Radicular low back pain
• Augmented design
• Residual effect
• Brinjal (Solanum melongena L
• Attributing characters
• Correlation studies
• Path analysis for yield
• BMC Genomics
• Feed efficiency
• Multi tissue analysis
• Residual feed intake
• RNA Seq
• Pig production industry
• báo cáo khoa học
• báo cáo hóa học
• công trình nghiên cứu về hóa học
• tài liệu về hóa học
• cách trình bày báo cáo
• tài liệu báo cáo nghiên cứu khoa học
• kiến thức vật lý
• báo cáo vật lý
• các nghiên cứu vật lý
• báo cáo y học
• công trình nghiên cứu về y học
• tài liệu về y học
• Research on flow characteristics in supercritical water natural circulation
• Influence of heating power distribution
• Passive residual heat removal system
• ANSYS CFX numerical analysis software
• End stage renal disease
• Peritoneal dialysis
• Short term mortality
• Cox model
• Residual glomerular filtration rate
• Basmati rice
• Correlation coefficients
• Path coefficient analysis
• Yield and its component traits
• BMC Cancer
• Competing risk
• Ovarian cancer
• Intraperitoneal chemotherapy
• Propensity score
• Subdistribution hazard ratio
• Developmental dysplasia of the hip
• Closed reduction
• Avascular necrosis
• Re dislocation
• Residual acetabular dysplasia
• Recurrent patellofemoral instability
• Lateral release
• Medial reefing
• Risk factors
• Functional outcome
• Residual complaints
• Native chickens
• Oxidative phosphorylation
• Colon cancer
• Relative survival analysis
• Emergency surgery
• Residual tumours
• Anaerobic digestion
• Residual poultry blood
• Activated carbon
• Volatile fatty acid
• Thermal analysis