TAILIEUCHUNG - Elastoplastic stability of thin rectangular plates under complex and impure loading

This paper deals with investigation of the elastoplastic stability of thin rectangular plates. The plate considered herein is subjected to the biaxial compressive forces which are assumed to be linearly distributed along every its edge. | Vietnam Journal of Mechanics, NCST of Vol. 23, 2001, No4 (205 - 215) ELASTOPLASTIC STABILITY OF THIN RECTANGULAR PLATES UNDER COMPLEX AND IMPURE LOADING Vu CONG HAM Le Quy don Technical University ABSTRACT. This paper deals with investigation of the elastoplastic stability of thin rectangular plates. The plate considered herein is subjected to the biaxial compressive forces which are assumed to be linearly distributed along every its edge. The governing equations of the problem are formulated with applying the elastoplastic process theory whereas Bubnov - Galerkin method is used to calculate the critical forces. In the paper the author proposes a new method to determine the elements of the matrix concerned with the instability moment of the structure and applies the Gaussian quadric method for integral calculation. Some results of numerical calculations are also presented in the paper. · 1. Introduction Let 's consider a thin rectangular plate which has the biaxial dimensions a, b and the thickness h. A coordinate orthogonal system Oxyz (or Ox 1 x 2 x 3 in tensor notations) is attached to the plate so that the plane Ox y coincides with the middle surface and the four edges can be mathematically described as x = 0, y == 0, x =a, y = b, respectively. In [2 , 3, 4, 5] . the so called pure loaded state is considered. According to this loaded state, the plate is subjected to one or any combination of biaxial compressive forces p, q and shear force T (figure 1) . These external forces are assumed to act in the middle surface and to be evenly distributed along every edge of the plate. Because of this, the prebuckling stress-strain state is pure at any point in the plate 205 This paper is concerned with the impure loading. The plate in the considered case is subjected to biaxial compressive forces p, q which are also assumed to act in the middle surface, but to be unevenly distributed along each edge, respectively. Because of mathematical difficulties, the .

• Cơ khí - Chế tạo máy
• Vietnam Journal of Mechanics
• Elastoplastic stability of thin rectangular plates
• Complex and impure loading
• The biaxial compressive forces
• Thin rectangular plates
• Dang Dinh Ang
• Nonlinear analysis and mechanics
• Dynamic problems involving stationary cracks
• The Wiener Hopt technique
• Dual integral equations
• Dual integrals in non linear fracture mechanics
• Non linear fracture mechanics
• Energy release rate
• Discuss the obtained
• The alpha finite element method (αFEM)
• Solid mechanics using triangular and tetrahedral elements
• Suitable computational cost
• NS FEM makes
• The upper bound property
• Non linear constitutive problems in solid mechanics
• Non linear constitutive problems
• Languages Gibian and special operators
• The application FEM
• Betts miller janjic convective parameterization scheme
• H14 31 model to forecast heavy rainfall in Vietnam
• Betts Miller Janjic
• Three rain seasons
• Manufacturing dry mixed cement mortar
• High compressive strength
• High flexural strength
• Low shrinkage and high watertightness for restoration
• Damaged hydraulic structures in Vietnam
• Standard gradient models and crack simulation
• Standard gradient models
• The propagation of cracks
• Damage mechanics and crack simulation
• The interaction between two parametric excitations
• The second and third degrees
• The asymptotic method of nonlinear mechanics
• Dynamic system governed
• Comparison of two hydrological model simulations
• Nam and Xinanjiang for Nong Son catchment
• The Central Vietnam
• The runoff components
• 3 D numerical simulation
• The tidal circulation
• The gulf of Tonkin
• The kinetic energy distribution
• Duality in the analysis of responses to nonlinear systems
• The analysis of responses
• The original nonlinear systems
• The study of nonlinear mechanics
• Aerodynamics of a wing in surface effect ship
• Theory and experiment
• Wing in surface effect ship
• The aerodynamic characteristics
• The Institute of Mechanics
• The error estimate
• The convergence rate for h
• p refinement
• The finite element analysis
• Three dimensional elastostatic mechanics problems
• Some initial experimental results
• Free water layer formation in horizontal pipes
• Water layer formation
• Hanoi Institute of Mechanics
• Bending vibration of beam elements under moving loads
• Considering vehicle braking forces
• Fluctuations of structures
• Beam elements according
• Continuous element for vibration analysis
• Thick shells of revolution
• Continous Element Method
• Finite element solutions
• Natural frequencies and harmonic responses
• Cast3m implementation of the extended finite element method
• The extended finite element method for cohesive crack
• Quasi brittle materia
• The proposed implementation
• The displacement discontinuities
• Buckling analysis of simply supported composite laminates subjected
• In plane compression load
• A novel mesh ffree method
• Alternative numerical technique
• Mesh free method
• A three story building
• Hedge algebras based fuzzy controller
• The structural system
• The El Centro earthquake
• Three story building against earthquake
• Laminar separation phenomenon combining with numerical calculations
• The turbulent separation
• The laminar separation
• Experimental study on mechanical properties
• Three phase polymer composite reinforced
• Glass fibers and titanium oxide particles
• Polymer composite reinforced
• Three phase composite
• Dynamic characteristics of elastically supported beam subjected
• A compressive axial force and a moving load
• The implicit Newmark method
• The Galerkin finite element method
• The axial force
• Eccentrically stiffened functionally graded plates and shallow shells
• Von Karman Donnell sense
• The formulation of governing equations
• The classical shell theory
• Mathematical modelling and control of the evolution
• Dynamic systems interacting with medium
• Mathematical modeling evolutional systems interacting
• Two conjugate mechanical subsystems
• Evaluating structural safety based on fuzzy set theory
• Evaluating structural safety
• The fuzzy reliability
• Simple beam structure