TAILIEUCHUNG - Fatigue crack growth at the representative zones in friction stir welding of a heat treatable aluminium alloy at 200oC

Although the grain microstructure of the TMAZ was significantly refined in comparison with that of BM, the FCG rate in TMAZ and base metal was shifted a comparable amount when the test temperature was elevated from room temperature to 200 oC. In the metallurgical view, the FCG rate in the fine grain TMAZ was higher than that in coarse grain HAZ and base metal site. | Vietnam Journal of Science and Technology 56 (1) (2018) 39-46 DOI: FATIGUE CRACK GROWTH AT THE REPRESENTATIVE ZONES IN FRICTION STIR WELDING OF A HEAT-TREATABLE ALUMINIUM ALLOY AT 200 oC Tran Hung Tra Nha Trang University, 2 Nguyen Dinh Chieu, Nha Trang, Viet Nam Email: tra@ Received: 16 June 2017; Accepted for publication: 6 November 2017 Abstract. Aluminium alloy 6063-T5 plates were joined by friction stir welding technique. The fatigue crack growth (FCG) in the thermo-mechanical affected zone (TMAZ) and in the heat affected zone (HAZ) of the welding was examined at 200 oC. Although the grain microstructure of the TMAZ was significantly refined in comparison with that of BM, the FCG rate in TMAZ and base metal was shifted a comparable amount when the test temperature was elevated from room temperature to 200 oC. In the metallurgical view, the FCG rate in the fine grain TMAZ was higher than that in coarse grain HAZ and base metal site. Keywords: aluminum alloy 6063-T5, friction stir welding, fatigue crack growth, HAZ, TMAZ, high temperature. Classification numbers: ; . 1. INTRODUCTION Aluminium alloys are one of the key materials possessing several advantages such as light weight, relatively low cost, heat treatable, high specific strength. Thus these alloys have been applied in the wide range of applications, especially in the aviation field [1]. However, one of the most challenges in using these alloys associates with their welding. Friction stir welding (FSW) is emerging as a preeminent technology for solving this obstacle. This FSW is suitable for joining light weight alloys such as aluminium alloys for both similar and dissimilar welding [2,3]. Furthermore, this FSW is recognized as a green technique in metal joining with high energy efficiency and versatility. This welding technique has been found to be a key joining technology in the near future. Since the welding can be obtained at the temperature below .

• Hoá học
• Vietnam Journal of Science and Technology
• Fatigue crack growth at the representative zones
• aluminum alloy 6063 T5
• friction stir welding
• fatigue crack growth
• Journal of Science
• Journal of Technology
• Technology Management
• Science and Technology
• International integration
• Journal of Marine Science and Technology
• Present state of ocean observations and service in Vietnam
• Unmanned Aerial Vehicle
• The Vietnam Academy of Science and Technology
• Ministry of Natural Resources and Environment
• Research Organizations
• Policy Planning
• Science and Technology development
• Theory Z
• Human Resources
• Development policy of Japan
• Technology and innovation system
• STI system
• Universities of Vietnam
• Model of Scientific Research
• Social Science Research System
• Nucleotide diversity of 15 conifer species in Vietnam’ s central highland
• Highland of Vietnam
• 15 conifer species
• Species of conifers
• Journal of Vietnam Agricultural Science and Technology
• Tạp chí Khoa học Công nghệ Nông nghiệp Việt Nam
• Agro food value chain
• Trade policy Vietnam
• Vietnam’s agricultural export
• The agricultural market
• The improved upland rice technology (IURT)
• Contract farming
• Improved technology
• Ssubsequent effect
• Application of passive remote sensin
• Upward looking microwave radiometers
• Technology Institute Vietnam Academy
• Trees canopyusing ground based
• Close innovation
• Open innovation
• Technological innovation
• Mechanical engineering
• R&D Organization
• Research activity
• Modeling studies of Vietnam lemongrass essential oil extraction process
• Lemongrass essential oil
• Response surface methodology
• Box Behnken design
• Kinetics of pyrolysis reaction
• Agricultural residues in Vietnam
• Corn cob and sugarcane bagasse
• Pyrolysis or gasification
• A hopane triterpenoid
• The mycelium of isaria japonica in Vietnam
• NMR assignment for 11β
• 22 dihydroxyhopane
• Spectral data analysis
• Seawater desalination applications in Vietnam
• Potential and challenges
• Current seawater desalination plants
• The MD process including configurations
• Characteristics of elemental and organic carbon
• Different sampling locations in vietnam
• NPs in the atmosphere
• Journal of Science and Technology
• Antibiotics and pesticides in water and sediments
• Intensive shrimp farms in southern Vietnam
• Mekong Delta Vietnam
• Arge amount of antibiotics
• Chemical constituents and biological activities
• Alpinia kwangsiensis collected in Vietnam
• Methanol extract of Alpinia kwangsiensis roots
• Staphylococcus aureus and Bacillus subtilis
• Wave characteristics in east Vietnam sea
• WAM cycle 4
• East Vietnam Sea
• Wave field Typhoon
• Using benthos to evaluate the quality
• The incident caused by formosa
• The central Vietnam
• The fungal strain FBV40
• Purification and characterization of laccase involved
• The white rot fungus isolated
• Bavi forest of Vietnam
• Study of sudden ionospheric disturbances
• Low frequency receiver
• Nha Trang province
• The sudden ionospheric disturbance
• Preliminary assessment of Btex
• Indoor and outdoor air
• Residential homes in Hanoi
• Among BTEX compounds