TAILIEUCHUNG - Development of a cold plug valve with fluoride salt

The final goal of the work is to provide useful recommendations and guidelines for the design of a cold plug for the emergency draining system of a molten salt reactor. Some numerical thermal simulations were performed with ANSYS mechanical (Finite Element Method) to be compared with results of the experiments and to make extrapolations for a new component to be used in a reactor. | Development of a cold plug valve with fluoride salt EPJ Nuclear Sci. Technol. 5 9 2019 Nuclear Sciences J. Giraud et al. published by EDP Sciences 2019 amp Technologies https epjn 2019005 Available online at https REGULAR ARTICLE Development of a cold plug valve with fluoride salt Julien Giraud2 Veronique Ghetta2 Pablo Rubiolo3 and Mauricio Tano Retamales1 1 Univ. Grenoble Alpes LPSC-IN2P3 38026 Grenoble Cedex France 2 CNRS LPSC-IN2P3 38026 Grenoble Cedex France 3 Grenoble INP Institute of Engineering University Grenoble Alpes LPSC-IN2P3 38026 Grenoble Cedex France Received 15 February 2019 Received in final form 21 June 2019 Accepted 27 June 2019 Abstract. Experimental studies have been developed on a new freeze plug concept for safety valves in facilities using molten salt. They are designed to allow the closure of an upstream circuit by solidifying the molten salt in a section of the device and to passively melt in case of a loss of electric power thus releasing the upper fluid. The working principle of these cold plug designs relies on the control of the heat transfer balance inside the device which determines whether the salt inside the cold plug solidifies or melts. The device is mainly composed of steel masses that are dimensioned to provide sufficient thermal heat storage to melt the salt and thus open the cold plug after the electric power is stopped. The final goal of the work is to provide useful recommendations and guidelines for the design of a cold plug for the emergency draining system of a molten salt reactor. Some numerical thermal simulations were performed with ANSYS mechanical Finite Element Method to be compared with results of the experiments and to make extrapolations for a new component to be used in a reactor. 1 Introduction Shut-off valves are designed to be capable of providing very low leakage when closed. In mechanical valves good Molten Salt Reactors have attracted increased attention in sealing is provided by

• Năng lượng
• Cold plug valve
• Emergency draining system
• Molten salt reactor
• Numerical thermal simulations
• Finite Element Method
• The finite element method
• Further topics
• The boundary element method
• Computational aspects
• Lecture Finite element method
• Basis equation of plane problem
• Finite element discretization
• Quadrilateral plane element
• Triangular plane element
• Introduction to the finite element method
• Finite element equations
• Heat transfer
• Fem for solid mechanics problems
• Finite elements
• The finite element method in engineering
• Interpolation models
• Isoparametric elements
• System equations
• Introduction to mechanics
• Fundamentals for finite element method
• FEM for beams
• FEM for frames
• FEM for Two Dimensional solids
• Finite element method using MATLAB
• CRC Mechanical engineering series
• Approximation techniques
• Finite element programming
• Direct approach
• Vietnam Journal of Mechanics
• Smoothed finite element method
• Two dimensional elasto plasticity
• The finite element
• The smoothed finite element method
• Mesh distortion and volumetric locking
• The isoparametric concept
• Higher order elements
• Adaptive finite element refinement
• The time dimension
• Couple systems
• Finite element analysis
• Computer procedures
• Locking phenomena in finite element analysis
• Deep beam and removal method
• Exhibit slow convergence
• Finite Element Methods
• Bài giảng Phương pháp phần tử hữu hạn
• Stiffness method
• Stiffness matrix
• Boundary conditions
• Lecture Structural analysis
• Finite element
• Structural analysis
• Finite element approach
• Element approach
• A first course in the finite element method
• Introduction to the stiffness method
• Development of truss equations
• Development of beam equations
• The plane stress
• Numerical method
• Electro Magnetic analysis
• Thermal analysis
• Axisymmetric elements
• Isoparametric formulation
• Three dimensional stress analysis
• Plate bending element
• Vibrational principles
• Galerkin approximation
• Partial differential equations
• Isoparametric finite elements
• Historical introduction
• Weighted residual
• Variational methods
• Elliptic problems
• Heat and fluid flow
• Some basic discrete systems
• Steady state heat conduction
• Transient heat conduction analysis
• Truss structures
• Elasticity problem
• Basic equations
• Solution procedure
• Three dimensional problems
• Dynamic analysis
• Cast3m implementation of the extended finite element method
• The extended finite element method for cohesive crack
• Quasi brittle materia
• The proposed implementation
• The displacement discontinuities
• The node based smoothed finite element method
• Free vibration problems
• The proposed formulation
• No spurious non zero energy modes
• Science and technology development
• Extended finite element method
• Simulating the mechanical behavior
• Multiple random holes and inclusions
• Functionally graded material
• The finite element method software
• Tạp chí khoa học và công nghệ
• Modeling the mechanical behavior
• Functionally graded material plates with multiple random inclusions
• Modeling of electromagnetic force
• Magnetic vector potential formulation via
• Sbproblem finite element method
• Subproblem finite element method
• Magnetic vector potential formulation