Đang chuẩn bị liên kết để tải về tài liệu:
Lab 5.2.6a Password Recovery Procedures

Đang chuẩn bị nút TẢI XUỐNG, xin hãy chờ

This lab demonstrates gaining access to a router with an unknown privileged mode (enable) password. One point to be made here is that anyone with this procedure and access to a console port on a router can change the password and take control of the router. That is why it is of critical importance that routers also have physical security to prevent unauthorized access. Setup a network similar to the one in the previous diagram. Any router that meets the interface requirements may be used. Possible routers include 800, 1600, 1700, 2500, 2600 routers, or a combination. Refer to the chart at the end of the. | Cisco SrsTEMS Lab 5.2.6a Password Recovery Procedures Router designation Router name Enable secret password Enable VTY and Console passwords Router 1 GAD class cisco Straight-through cable Serial cable Console Rollover Crossover cable Objective Gain access to a router with an unknown privileged mode enable password. Background Preparation This lab demonstrates gaining access to a router with an unknown privileged mode enable password. One point to be made here is that anyone with this procedure and access to a console port on a router can change the password and take control of the router. That is why it is of critical importance that routers also have physical security to prevent unauthorized access. Setup a network similar to the one in the previous diagram. Any router that meets the interface requirements may be used. Possible routers include 800 1600 1700 2500 2600 routers or a combination. Refer to the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the lab. The configuration output used in this lab is produced from 1721 series routers. Any other router used may produce slightly different output. The following steps are intended to be executed on each router unless specifically instructed otherwise. Start a HyperTerminal session as performed in the Establishing a HyperTerminal session lab. Note Configure the hostname and passwords on the router. Have an instructor lab assistant or other student configure a basic configuration with an enable secret password. Perform copy running-config startup-config and reload the router. Note The version of HyperTerminal provided with Windows 95 98 NT and 2000 was developed for Microsoft by Hilgraeve. Some versions may not issue a break sequence as required for the Cisco router password recovery technique. If this is the case upgrade to 1 - 5 CCNA 2 Routers and Routing Basics v 3.0 - Lab 5.2.6a Copyright 2003 Cisco Systems Inc. HyperTerminal Private Edition PE .

TÀI LIỆU LIÊN QUAN
TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.