TAILIEUCHUNG - Cách xếp bọ ngựa bằng giấy

Tham khảo tài liệu 'cách xếp bọ ngựa bằng giấy', văn hoá - nghệ thuật, khéo tay hay làm phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Praying Mantis by Robert J. Lang Copyright 1990. All rights reserved. I I 2. Fold and unfold. 3. First make the horizontal crease halfway between the two pinch marks. Then make the vertical crease through the intersection of the horizontal crease and the diagonal of the square. 4. Fold the corners in and turn 5. Fold a Waterbomb Base the paper over. based on the new creases. using the program Aldus FreeHand linked withadditional PostScript routines that were coded by the author. The design and these drawings may not be distributed commercially. I ra in 7. Fold and unfold. 8. Open-sink the corner. I 10. Reverse-fold the corner. 9. Open out the sink and push some paper up from the inside pinch the excess paper in half and swing it over to the left. 11. Pull down the edge of the pocket and fold the right layer back to the left. 12. Fold one flap down. 15. Squash-fold. 13. Swing one layer from right to left. 14. Repeat steps 6-13 on the right. 16. Petal-fold. 17. Unwrap a single layer. 18. Squash-fold. 19. Reverse-fold the edges. 20. Turn the model over. 21. Repeat steps 15-17. 24. Reverse-fold a single 25. Reverse-fold layer out from the inside. 22. Fold and 23. Fold the flap down using the unfold. newly-made creases as a guide. 29. Flatten the edges. 26. Reversefold the bottom corner. 27. Pull out the layers trapped under the triangular hood. The model will not lie flat. 28. Open-sink the shaded region and refold. 30. Fold and 31. Fold one the sunk unfold. layer to the left region. in front and one to the right behind. 32. Top of the model. Fold and unfold. 33. Pleat and fold a rabbit ear from the thick point using the existing creases. 34. Fold and unfold through all layers. 35. Wrap one layer of paper to the front. 36. Fold one layer to the right releasing the trapped paper at the left that links it to 37. In progress. Pull paper out from here. 38. Close the model back up. 39. Repeat steps 36-38 on the next two layers. 40. Swing the point over to the left . the

TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.