TAILIEUCHUNG - Complete Hardware Guide phần 3

kết nối cho tất cả các thiết bị trong các rack. Việc chuyển đổi EX4500 là 2 đơn vị giá (2 U) kích thước. Mỗi chuyển mạch EX4500 được thiết kế để tối ưu hóa việc sử dụng không gian rack và hệ thống cáp. Xem hình 1 trên trang 4, Hình 2 ở trang 4, và Hình 3 ở trang 5. | Complete Hardware Guide for EX4500 Ethernet Switches Table 10 Power Supply LED on EX4500 Switches continued LED State Description Green On steadily Power supply is functioning normally. Blinking Power supply has failed. Amber On steadily Power supply has failed. Blinking Power supply has failed. Related Documentation AC Power Specifications for EX4500 Switches on page 85 AC Power Cord Specifications for an EX4500 Switch on page 86 Connecting AC Power to an EX4500 Switch on page 127 DC Power Supply in EX4500 Switches The DC power supply in EX4500 switches is a hot-insertable and hot-removable field-replaceable unit FRU . EX4500 switches are shipped with one power supply. A cover panel is installed in the second power supply slot. You can add a second power supply to the switch. Power supplies are installed at the rear of the chassis in slots labeled 1 and 0. Both power supplies are accessible from the rear of the chassis. WARNING The switch is pluggable type A equipment installed in a restricted-access location. It has a separate protective earthing terminal provided on the chassis in addition to the grounding pin of the power supply cord. This separate protective earthing terminal must be permanently connected to earth ground. See Connecting Earth Ground to an EX Series Switch on page 119. Each DC power supply weighs approximately 3 lb kg and has a pair of DC input lugs -48 VDC and RTN on the front of the power supply. Each DC power supply also has a fan a bicolor LED on the faceplate that indicates the status of the power supply and a colored ejector lever. See Figure 16 on page 31. 30 Copyright 2011 Juniper Networks Inc. Chapter 2 Component Descriptions Figure 16 DC Power Supply DC terminal block Ejector lever Power supply LED Power supply handle NOTE A1200 W DC power supply requires a dedicated 30 A circuit breaker for the input DC feed. Each DC power supply has an ejector lever that holds the power supply in place. The ejector lever locks into the .

TỪ KHÓA LIÊN QUAN
TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.