TAILIEUCHUNG - Fourier Transforms in Radar And Signal Processing_ part 8

Biến đổi Fourier được sử dụng hàng ngày để giải quyết các chức năng duy nhất và sự kết hợp của các chức năng được tìm thấy trong các máy radar và xử lý tín hiệu. Tuy nhiên, nhiều vấn đề có thể được giải quyết bằng cách sử dụng biến đổi Fourier đã đi chưa được giải quyết bởi vì họ yêu cầu hội nhập đó là quá tính toán khó khăn. Hướng dẫn sử dụng này thể hiện như thế nào bạn có thể giải quyết những vấn đề hội nhập nhiều với một cách tiếp cận để. | Array Beamforming 185 separation d wavelengths by a pseudorandom step chosen within an interval of width d which ensures that the elements are at least half a wavelength apart. Figure a shows the response in u space for an array of 21 elements at an average spacing of 2 3. A sector beam of width 40 degrees centered at broadside was specified. A regular array would have a pattern repetitive at an interval of in u and this is shown by the dotted response. The irregular array repetitions are seen to degrade rapidly but the pattern that matters is that lying in the interval 1 1 in u. This part of the response leads to the actual pattern in real space shown in Figure b . We note that the side lobes are up to about 13 dB rather poorer than for the patterns from regular arrays shown in Figures and though this level varies considerably with the actual set of element positions chosen. The integration interval I was chosen to be 1 1 to give the least squared error solution over the full angle range from 90 degrees to 90 degrees and its reflection about the line of the array . A second example is given in Figure for an array of 51 elements but illustrating the effect of steering. In Figure a b the 40-degree beam is steered to 10 degrees and again we see the rapid deterioration of the approximate repetitions in u space of the beam and a nonsymmetric side-lobe pattern though the levels are roughly comparable with those of the first array. The average separation is wavelengths giving a repetition interval of in u. If we steer the beam to 30 degrees Figure c d there is a marked deterioration in the beam quality. This is because one of the repetitions falls within the interval I over which the pattern error is minimized so the part of this beam near u 1 that should be zero is reduced. At the same time the corresponding part of the wanted beam near u 1 2 should be unity so the solution tries to hold this level up. We note that

TỪ KHÓA LIÊN QUAN
TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.