TAILIEUCHUNG - cisco voice over ip cvoice authorized self study guide phần 3

cho phép công nhận tích cực của tín hiệu mặt đất kết nối và ngắt kết nối. Bởi vì tín hiệu mặt đất bắt đầu sử dụng một yêu cầu và /hoặc xác nhận chuyển đổi ở cả hai đầu của giao diện, nó là một lợi thế hơn FXOs và phương pháp truyền tín hiệu khác trên thân cây cao-sử dụng. | 138 Authorized Self-Study Guide Cisco Voice over IP CVOICE Idle State CO PBX FXO 1 1 Tip Tip Ground I 1 1 Detector _1 1 RG -T- Ring 1 -48V On-Hook PBX Grounds Ring Lead CO Senses Ring @ Ground and Grounds Tip Lead CO JL------ RG x -48V Tip Ring PBX FXO Tip _ Ground Detector -----ZL On-Hook PBX Senses Tip Ground Closes Two Wire Loop and Removes Ring Ground CO _Ẹ------ RG x -48V Tip Ring PBX FXO Tip Ground Detector On-Hook Figure 3-11 Ground-Start Signaling Ground-start signaling works by using ground and current detectors that allow the network to indicate off-hook or seizure of an incoming call independent of the ringing signal and allow for positive recognition of connects and disconnects. Because ground-start signaling uses a request and or confirm switch at both ends of the interface it is preferable over FXOs and other signaling methods on high-usage trunks. For this reason groundstart signaling is typically used on trunk lines between PBXs and in businesses where call volume on loop-start lines can result in glare. The ground-start signaling process is as follows Step 1. In the idle state both the tip and ring lines are disconnected from ground. The PBX and FXO constantly monitor the tip line for ground and the CO and FXS constantly monitor the ring line for ground. Battery -48 VDC is still connected to the ring line just as in loop-start signaling. Step 2. A PBX or FXO grounds the ring line to indicate to the CO or FXS that there is an incoming call. The CO or FXS senses the ring ground and then grounds the tip lead to let the PBX or FXO know that it is ready to receive the incoming call. Step 3. The PBX or FXO senses the tip ground and closes the loop between the tip and ring lines in response. It also removes the ring ground. Chapter 3 Routing Calls over Analog Voice Ports 139 Analog Address Signaling The dialing phase allows the subscriber to enter a phone number address of a telephone at another location. The customer enters this number with either a .

TỪ KHÓA LIÊN QUAN
TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.