TAILIEUCHUNG - Effects of plasma treatment and sanding process on surface roughness of wood veneers

An ideal veneer surface is crucial for good panel properties in plywood manufacturing. The aim of this study was to compare plasma treatments and sanding (mechanical) processes with respect to the surface roughness of veneers. Rotary-cut veneers with a thickness of 2 mm from Scots pine (Pinus sylvestris) logs were used as material. | Turkish Journal of Agriculture and Forestry Research Article Turk J Agric For (2014) 38: 663-667 © TÜBİTAK doi: Effects of plasma treatment and sanding process on surface roughness of wood veneers 1, 1 2 2 2 Cenk DEMİRKIR *, İsmail AYDIN , Semra ÇOLAK , Gürsel ÇOLAKOĞLU Department of Woodworking Industry Engineering, Faculty of Technology of Of, Karadeniz Technical University, Trabzon, Turkey 2 Department of Forest Industry Engineering, Faculty of Forestry, Karadeniz Technical University, Trabzon, Turkey Received: Accepted: Published Online: Printed: Abstract: An ideal veneer surface is crucial for good panel properties in plywood manufacturing. The aim of this study was to compare plasma treatments and sanding (mechanical) processes with respect to the surface roughness of veneers. Rotary-cut veneers with a thickness of 2 mm from Scots pine (Pinus sylvestris) logs were used as material. After rotary peeling, veneer sheets were dried at 110 °C in a veneer dryer. Veneer sheets were divided into 4 main groups. The surfaces of the control veneer sheets were left untreated. Two different grits of sandpaper, 80 and 180, were used for sanding the surfaces of veneers. Plasma treatment was applied to the last veneer group with 3 different gases (oxygen, nitrogen, and ammonia) and 3 different plasma times (1 min, 5 min, and 15 min). The Mitutoyo Surftest SJ-301 instrument was used to determine surface roughness of samples. Average roughness (Ra), mean peak-to-valley height (Rz), and maximum roughness (Rmax) parameters were measured to evaluate the surface roughness of the samples based on DIN 4768. It was found that the smoothest veneer surfaces were obtained with the sanding processes. Surface roughness values (Rz) of veneer sheets sanded with 180 grit sandpaper were lower than those of veneers sanded with 80 grit sandpaper. Compared with the .

TỪ KHÓA LIÊN QUAN
TAILIEUCHUNG - Chia sẻ tài liệu không giới hạn
Địa chỉ : 444 Hoang Hoa Tham, Hanoi, Viet Nam
Website : tailieuchung.com
Email : tailieuchung20@gmail.com
Tailieuchung.com là thư viện tài liệu trực tuyến, nơi chia sẽ trao đổi hàng triệu tài liệu như luận văn đồ án, sách, giáo trình, đề thi.
Chúng tôi không chịu trách nhiệm liên quan đến các vấn đề bản quyền nội dung tài liệu được thành viên tự nguyện đăng tải lên, nếu phát hiện thấy tài liệu xấu hoặc tài liệu có bản quyền xin hãy email cho chúng tôi.
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.