TAILIEUCHUNG - Manual for induction motors and generators

Electric machines have dangerous live and rotaling parts and may hot surfaces. All operations serving transport, storage, installation, connection, commissioning. operation and mailntenance shall be canied uot by responsible skilled persons. | Manual for Induction Motors and Generators a mi A Manual for Induction Motors and Generators Safety Instructions AMA AMB AMG AMH AMK AMZ HXR M3BM M3GM 1. General General safety regulations specific agreements made for each work site and safety precautions shown in this document must be observed at all times. 2. Intended use Electric machines have dangerous live and rotating parts and may have hot surfaces. All operations serving transport storage installation connection commissioning operation and maintenance shall be carried out by responsible skilled persons in conformity with EN 50 110-1 DIN VDE 0105 IEC 60364 . Improper handling may cause serious personal injury and damage to property. Danger These machines are intended for industrial and commercial installations as components as defined in the Machinery Directive MD 98 37 EC. Commissioning is prohibited until conformity of the end product with this directive has been established follow particular local safety and installation rules as for example EN 60204 . These machines comply with the harmonized series of standards EN 60034 DIN VDE 0530. Their use in explosive atmosphere is prohibited unless they are expressly designed for such use follow additional instructions . On no account use degrees of protection IP23 outdoors. Air-cooled models are typically designed for ambient temperatures of -20 C up to 40 C and altitudes of 1000 m above sea level. Ambient temperature for air- water-cooled models should be not less than 5 C for sleeve-bearing machines see manufacturer s documentation . By all means take note of deviating information on the rating plate. Field conditions must conform to all rating plate markings. 3. Transport storage Immediately report damage established after delivery to transport company. Stop commissioning if necessary. Lifting eyes are dimensioned for the weight of the machine do not apply extra loads. Ensure the use of correct lifting eyes. If necessary use suitable adequately dimensioned .

• Điện - Điện tử
• Induction motor
• generator
• engineering technology
• electrical appliances
• electrical engineering textbooks
• electronic applications
• Dynamic model of the induction motor
• The induction motor
• Chapter 6 dynamic model
• Chapter 6 dynamic model of the induction motor
• Space vectors of motor variables
• Revolving reference frame
• Uncontrolled induction motor drives
• Operation of uncontrolled
• Uncontrolled induction motor
• Chapter 3 uncontrolled induction motor drives
• Braking and reversing
• System with starting impedances
• Journal of Automation and Control Engineering
• Decreasing induction motor loss using reinforcement learning
• Decreasing induction motor loss
• The motor works
• The standard driver of motor
• Power electronic converters
• Induction motor drives
• Power electronic converters for induction motor drives
• Chapter 3 power electronic converters
• Control of stator voltage
• Control Of voltage source inverters
• Harmonic analysis of 3 Phase induction motor
• PT indocement Tunggal Prakarsa
• 3 Phase induction motor
• The fundamental harmonic magnetic field
• Causing higher noise
• Total Harmonic Distortion
• Passive single tuned filter
• Phd thesis summary
• Adaptive control for six phase induction motor drives
• Adaptive control
• Six phase induction motor drives
• Improve control quality
• Fault detection and protection of induction motor
• Real time monitoring
• Controlling of the motor parameters
• Programmable Logic Controller
• Open end winding induction motor
• Switched boost inverter
• Z source inverter
• Motor configuration
• DC DC converter
• Electronic Engineering
• Dual rotor permanent magnet induction motor
• Electromagnetic field
• Finite element method
• Mathematical model
• Closed Loop
• Torque Angle Control
• Direct Torque Control
• Estimated currents
• Faulttolerant control
• Induction motor drive by applying space vector
• Current sensor failures
• Enhanced fault tolerant control
• Bài giảng Điều khiển máy điện
• Điều khiển máy điện
• Scalar Control of Induction Motor
• Space Vector PWM
• Điều khiển vô hướng
• Luật điều khiển V/f
• Power Electronics and Motor Drives
• Introduction and Perspective
• Power Semiconductor Devices
• Computer Simulation and Digital Control
• Non linear control
• Direct decoupling
• Current sensorless
• Estimated stator currents
• eld oriented control
• Hysteresis controller
• Direct field oriented control
• Induction motor
• Estimate speed
• Low cost
• Machine model
• Motor Powered
• Voltage Quality
• Particle Swarm
• Induction Machines
• PWM Inverter
• Helical Motion
• Electromechanical energy conversion
• Lecture Electromechanical energy conversion
• Electromechanical energy
• Polyphase Induction Machines
• Motor equivalent circuit
• Equivalent circuit
• Scheme
• Information Technology
• Electrical Engineering
• thesis
• Motor Control
• power electronics
• Động cơ cảm ứng
• Ước lượng tốc độ
• Điều khiển động cơ
• Mạng nơron
• Speed estimation
• Neural network
• Tự động hóa
• Cơ khí chế tạo máy
• Điện – điện tử
• Kiến trúc xây dựng
• kỹ thuật viễn thông
• transformers
• power electronic
• machinery fundamentals
• synchronous generation
• synchronous motor
• induction motors
• Năng lượng